Press the ON button to turn on the printer.ī. If the Stop button is pressed 5 or 6 times, and the ON LED keeps flashing, try the following:Ī. While holding down the ON button, press the Stop button 6 times.) If the printer fails to enter Service Mode, turn off the printer and repeat steps No.1 - 6, and in step No.4, press the Stop button 6 times (4. If steps No.1 - 6 have been carried out correctly, but the ON LED continues to flash, it means the printer failed to enter Service Mode. Service Tool cannot be used to reset the printer if the printer is connected to a computer with a Wireless connection. Service Tool can be used to reset the printer if the printer is connected to a computer with a USB cable. After the printer enters Service Mode, open the Service Tool and do a reset. If the ON LED is green (not flashing) it means that the printer has entered Service Mode.ħ. Wait for a while, the ON LED will flash and finally turn green. When finished pressing the Stop button 5 times, then release the ON button.Ħ. While holding down the ON button, press the Stop button 5 times.ĥ. Release only the Stop button, while the ON button is still being held.Ĥ. Now both buttons (Stop and ON) are still being held.ģ. Press and hold the ON button (do not release). Press and hold the Stop button (do not release)Ģ. The printer is off, the power cable is connected to a power source, and the printer is connected to the computer with a USB cable.ġ. Reset can be done if the printer is in Service Mode.
SERVICE TOOL V4905 KUYHAA MANUAL
What I'm afraid of is that incorrect information about the "Printer Support Service Tool" will provoke users to try different Service Tools, to reset the printer, because in the Service Manual document only says "use Service Tool version A" or "use Service Tool version A or leter". So I can only say ST.4718 and ST.4720 have the same interface, so the functions might be the same, but I don't dare to say that ST.4718 for printers A, B, C, etc, or ST.4720 for printer A, B, C, etc, because there is no service manual document that states it.
SERVICE TOOL V4905 KUYHAA SERIES
I do not dare to say that Service Tool version A, supports printer series A, B, C, D, etc., as most sites write, because there is no evidence that the Service Manual document says that. The post that I wrote, is based on the Service Manual, and the Service Tool used to reset, according to the information in the Service manual. If I match the information in the Service Manual and information on the internet, about "Sevice Tool Support Printer", there are many differences. A lot of information on the internet that, Service Tool supports Canon printers series A, B, C, D, etc. Important information that we must know from the Service Tool is the "Printer Support Service Tool". Based on the image information in the manual document above, because the interfaces of the three tools are the same, I concluded that the functions of the three Service Tools are the same. There are 4 tabs provided, namely Main, Other, Auto, and Pro.
SERVICE TOOL V4905 KUYHAA CRACK
The crack version of ST.4720 is easy to get on the internet, unfortunately ST.4720 is infected with HackTool.Agent (scan with Malwarebytes)Īll three Service Tools have the same interface. For ST.4718 I found this file in the kelvenbox tool.ģ. Canon released ST.4710, and unfortunately information about this service tool is not yet available on the internet.Ģ. Other pages in this document explain the function button, "Service Tool v.4718".ġ. In the document "Canon G1000 series, G2000 series, G3000 series Service Manual" written to reset, use ST.4710 or leter. In my opinion, Service Tool v.4718 and Service Tool v.4720 are the same. Turn on printer and printer ready to use.
If the value of D=000.0 means that the waste ink absorber has been reset to zero. Make sure, the waste ink absorber has been replaced with a new one, before you reset the D value.
Print EEPROM (1) information once again after resetting.Set Destination, select your Region (4): ASA (Asia), AUS (Australia), BRA (Brazil), CHN (China), CND (Canada), EMB (Middle East), EUR (Europe), JPN (Japan), KOR (Korea), LTN (Latin), TWN (Taiwan ), USA (United States) and then click SET (5).Clear Ink Counter, select ALL (2), and then click SET (3). After resetting, the ink absorber counter value is printed automatically.For your reference in servicing, print EEPROM (1) information before resetting.